Chat with us, powered by LiveChat
Sale!

PD32 Fenix Flashlight

Max Lumens: 900
Modes: 7
(26 customer reviews)

$82.00 $61.95

The upgraded PD32 LED flashlight from Fenix now lights your way with 900 max lumens from one 18650 Li-ion battery or two CR123As. Choose between 5 brightness levels, for a maximum beam distance of 787ft, as well as strobe and S.O.S. modes. Tap and hold the tactical tail switch for a fast momentary on and the side switch to access the different modes. The PD32 LED flashlight is perfect for hiking, camping and outdoor activities and is powerful enough for law enforcement and search/rescue.
For commercial orders and large purchases, contact us at (888) 775-9996 x6, or
GET A QUOTE
WARNING. Be aware of counterfeit Fenix merchandise in the U.S. marketplace.
READ MORE

Max Lumens: 900
Modes: 7

Description

pd32 flashlight specs chart

Size:
Length: 5.1” (129.5mm)
Body: 0.9” (22.6mm)
Head: 0.9” (24mm)

Weight: 2.7 oz. (77g) excluding battery

Batteries (not included): One 18650 Li-ion battery or two CR123A batteries

Included: Holster, body clip, lanyard, spare O-ring, spare rubber switch boot

Warranty: Limited Lifetime Guarantee from Fenix Lighting US

  • Uses Cree XP-L HI white LED with a lifespan of 50,000 hours
  • Digitally regulated output maintains constant brightness
  • Compatible with AER-01 and AER-02 remote pressure switch
  • Low voltage reminder indicates when battery replacement is needed
  • Reverse polarity protection, to protect from improper battery installation
  • Over-heat protection to avoid high temperature of the surface
  • Anti-roll and anti-slip body design, capable of tail standing
  • Tactical tail switch, momentary-on function
  • Side switch for light-dimmer and mode shifting
  • Made of durable aircraft-grade aluminum
  • Premium type Ⅲ hard-anodized anti-abrasive finish
  • Toughened ultra-clear glass lens with anti-reflective coating

 

Operation Instruction

ON/OFF
Tap the tail switch to momentarily turn on the light, release it the light goes out.
Fully press the tail switch to turn ON/OFF the light.

Output Selection
With the light on, single-click the side switch to cycle through Turbo→Low→Mid→High→Eco.

Strobe and SOS
With the light on, press and hold the side switch for 0.5 seconds to enter into Strobe mode.
Under Strobe mode, single-click the side switch to cycle through Strobe→SOS.
Then press and hold the side switch for 0.5 seconds to turn back to General mode.

Intelligent Memory Circuit
The flashlight memorizes the last-used brightness level in the General mode, but not Strobe and SOS. The next time you turn on the flashlight, it will activate the last brightness level you selected.

Over-heat Protection
The flashlight will accumulate a lot of heat when it is working at Turbo and High brightness level. When it works at Turbo for 3 minutes or at High for 30 minutes, the flashlight will automatically downshift to lower output to prevent the light from overheating. If the Turbo or High output is needed, please reset it again. The flashlight could be damaged or the normal service life would be shortened because of continuous use like this.

Low-voltage Warning Function
If low voltage is detected, the flashlight is programmed to downshift to a lower brightness level until to Eco brightness level. When this happens at Eco output mode, the flashlight blinks three times every five minutes to remind you to replace the battery. To ensure normal use, the flashlight will not turn off automatically and will work until the battery runs out completely.

ON/OFF
Tap the tail switch to momentarily turn on the light, release it the light goes out.

Fully press the tail switch to turn ON/OFF the light.

Output Selection
With the light on, single-click the side switch to cycle through Turbo→Low→Mid→High→Eco.

Strobe and SOS
With the light on, press and hold the side switch for 0.5 seconds to enter into Strobe mode.

Under Strobe mode, single-click the side switch to cycle through Strobe→SOS.

Then press and hold the side switch for 0.5 seconds to turn back to General mode.

Intelligent Memory Circuit
The flashlight memorizes the last-used brightness level in the General mode, but not Strobe and SOS. The next time you turn on the flashlight, it will activate the last brightness level you selected.

Over-heat Protection
The flashlight will accumulate a lot of heat when it is working at Turbo and High brightness level. When it works at Turbo for 3 minutes or at High for 30 minutes, the flashlight will automatically downshift to lower output to prevent the light from overheating. If the Turbo or High output is needed, please reset it again. But the flashlight could be damaged or the normal service life would be shortened because of continuous use like this.

Low-voltage Warning Function
If low voltage is detected, the flashlight is programmed to downshift to a lower brightness level until to Eco brightness level. When this happens at Eco output mode, the flashlight blinks three times every five minutes to remind you to replace the battery. To ensure normal use, the flashlight will not turn off automatically and will work until the battery runs out completely.

Battery Replacement
Unscrew the tail cap to insert the battery with the anode side (+) towards the light head, and then screw the tail cap.

Usage and Maintenance

  • Disassembling the sealed head can cause damage to the light and will void the warranty.
  • Fenix recommends using excellent quality battery. If the lamp will not be used for an extended period, remove the battery, or the lamp could be damaged by electrolyte leakage or battery explosion.
  • Unscrew the tail cap one-half turn or take out the battery to prevent accidental activation during storage or transportation.
  • Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare.
  • Periodic cleaning of the battery contacts improves the lamp’s performance as dirty contacts may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following reasons:
    Reason A: The batteries need replacing.
    Solution: Replace batteries (Please confirm the correct installation of anode and cathode).
    Reason B: The threads, PCB board contact or other contacts are dirty.
    Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol.

If the above methods don’t work, please refer to the warranty policy before contacting your authorized distributor.

Notice: The routine cleaning video can be watched and downloaded through Fenix official website, please log onto the service channel->“maintenance for light”.

Warning
The flashlight is a high-intensity lighting device capable of causing eye damage to the user or others. Avoid shining the flashlight directly into anyone’s eyes.

26 reviews for PD32 Fenix Flashlight

  1. Chris (verified owner)

    PD32 2016. Excellent light. Has all the output settings I could want.

    I give only four stars because of the side control button. It’s difficult to operate when contorted around a piece of machinery, or an engine bay, or during night hunts.

    FENIX: I propose a PD33. Same outputs as the PD32 but all controlled by the tail switch. Or even just give an Eco, Medium, Turbo, and Strobe control from the tail switch. And the other options from the side button.

    Thanx

    1 out of 2 people found this helpful. Was this review helpful to you?
Add a review

Your email address will not be published. Required fields are marked *

What Our Ambassadors Say

Daniel T

Fenix PD32 Flashlight Review

Daniel T.
Tactical Ambassador, Daniel T., Reviews the PD32 Flashlight Throughout each of my professions, and my charity work, I regularly carry only a few items for each activity. Of those, only one makes the cut for every one of the activities, all the time. That's my Fenix PD32. As a firearms instructor, I use my PD32…

You may also like…

Menu