Chat with us, powered by LiveChat
Sale!

Fenix PD25 Custom Engraved Flashlight – Religious

(1 customer review)

$79.00 $56.95

Clear
CHOOSE YOUR MARK:
SKU: N/A Category:

The Fenix PD25 is a powerful, tiny flashlight featuring the latest Cree XP-L LED. This flashlight produces max 550-lumen and 427ft beam distance from a 16340 rechargeable Li-ion battery. The tail cap switch provides momentary-on function while the side switch on the head is for output selection. The Fenix PD25 flashlight is perfect for the outdoors or your every day needs.

Description

fenix pd25 flashlight specification chart

Size:
Length: 3.7” (93mm)
Width: 0.8” (21.5mm)

Weight: 1.7 oz. (47g) weight excluding battery

Batteries: One 16340 rechargeable Li-ion (included) or 3V CR123A Lithium battery

Included: ARB-L16-700U USB rechargeable battery, lanyard, holster, body clip, and spare O-ring

Warranty: Limited Lifetime Guarantee from Fenix Lighting U.S.

  • Utilizing Cree XP-L V5 LED with a lifespan of 50,000 hours
  • Digitally regulated output – maintains constant brightness
  • Low-voltage warning function to remind you to replace the battery
  • Reverse polarity protection, to protect from improper battery installation
  • Over-heat protection to avoid high-temperature of the surface
  • Anti-roll, slip-resistant body design
  • Tactical tail cap switch with momentary-on function
  • Side switch on the head for output selection
  • Made of durable aircraft-grade aluminum
  • Premium Type III hard-anodized anti-abrasive finish
  • Toughened ultra-clear glass lens with anti-reflective coating

Note: The above-parameters (lab tested by Fenix using a CR123A Lithium battery and a 16340 rechargeable Li-ion battery) are approximate and may vary between lights, batteries and environments.

 

ON/OFF
Press the tail switch gently for momentary-on lighting or until it clicks to activate and lock the PD25. Press again to turn the light off.

Mode Selecting
With the light on, press the side switch to cycle through four different brightness levels from Turbo → Low → Mid → High.

Strobe Mode
Press the side switch and hold it for 0.8 seconds to enter into Strobe mode.

When the flashlight is in strobe mode, a single press on the side switch will return the light to general lighting mode.

Intelligent Memory Circuit
The Fenix PD25 memorizes the last brightness level used in the general mode, but it will not remember the strobe mode. The next time you turn the flashlight on, it will activate the last brightness level you selected.

Over-heat Protection
PD25 will accumulate a lot of heat when it is working in Turbo output. To avoid overheating, the flashlight will automatically transfer into the high brightness level by working in Turbo output for over 5 minutes. If the Turbo output is needed continually, just reset it again.

Low-voltage Warning Function
When the voltage level drops below the preset level, the PD25 is programmed to downshift to a lower brightness level. When this happens in Low output mode, the flashlight blinks three times every five minutes to remind you to replace the battery.

Note: The function only works when the light is powered by 16340 rechargeable Li-ion battery. If the voltage of the 16340 battery drops below 3V, this function will be invalid when the light is turned off and then on again.

Battery Replacement
Unscrew the light head to put in the battery with the anode (+) toward the light head, then align the threads and screw the light head back on.

Usage and Maintenance

  • Please don’t disassemble the sealed head, doing so can cause damage to the flashlight and will void the warranty.
  • We recommend the use of high quality battery. If the flashlight is not to be used for an extended period, remove the battery, or the flashlight could be damaged by electrolyte leakage or battery explosion.
  • Unscrew the tail cap one-half turn or take out the battery to prevent accidental activation during storage or transport.
  • The O-ring may be worn out after using for a long time. If this happens, please replace the O-ring with a new one to keep the flashlight properly sealed against water.
  • Please clean the contacts of your light from time to time, especially if the light flickers or doesn’t light up. There may be several reasons for a flickering or not working light:
    Reason A: The battery needs replacing.
    Solution: Replace the battery (Please confirm the correct orientation of positive and negative ends).
    Reason B: The threads, PCB board contact or other contacts are dirty.
    Solution: Clean the contact points with an alcohol soaked cotton swab.

If the above methods don’t work, please refer to the warranty policy.

Notice: The routine cleaning video can be watched and downloaded through Fenix official website, please click the service channel->“maintenance for light”.

Warning
The PD25 is a high-intensity lighting device capable of causing eye damage. Avoid shining the light directly into anyone’s eyes.

Add a review

Your email address will not be published. Required fields are marked *

You may also like…

Menu